HowToDoThings.com Tools & Materials

How To Implement Heating Efficiency Ideas

johnnyhayneser — Tue, 29 Jan 2008 15:52:31 -0600

Saving money on your water heater is a great idea. There are so many different things you can do to save hundreds of dollars per year with very little work. Let's review some things to look for when dealing with the different types of plumbing parts associated with water heaters.

How To Remove Sediment from a Water Heater

johnnyhayneser — Fri, 25 Jan 2008 14:06:19 -0600

All water that enters into a water heater contains natural minerals of some kind. Heating the water causes the minerals to separate and fall to the bottom of the tank. Usually this sediment build-up is made of calcium carbonate. One sign of sediment build-up is a sulfur (or rotten-egg) smell around your water heater. With gas water heaters, sediment problems may cause the entire heater to become noisy while on.

How To Snap a Chalk Line

Larado — Fri, 18 Jan 2008 14:09:00 -0600

Most people snap a chalk line for one reason: They need a line to follow. You could be laying tile, or framing a room, or even just cutting a large board. Whatever the reason, being able to snap a chalk line is a very useful skill that is frequently needed for projects around the house.

Items needed:

Chalk box
An assistant
Hammer
Nail
Tape measure

Instructions:

How To Upgrade Your Water Heater's Drain Valve

johnnyhayneser — Tue, 04 Dec 2007 10:58:34 -0600

The drain valve is located near the bottom of the water heater tank. Many water heaters come with drain valves that are prone to leaks or breakage. Plastic cone valves (these have a cone-shaped handle) and plastic faucet valves often drip, freeze and/or clog with sediment. Even after only one use, plastic valves often leak. Also, because the drain valve is made of plastic, the threads on the valve are easy to cross-thread when attaching a garden hose to it.

How To Keep Your Electric Heating Elements from Failing

johnnyhayneser — Mon, 03 Dec 2007 16:41:51 -0600

The following applies to electric water heaters only. The heating elements in an electric water heater are susceptible to sediment buildup, burnout and sudden failure. Learn how to clean and inspect the heating elements in your electric water heater.

How To Prevent Rusting in a Water Heater

johnnyhayneser — Mon, 03 Dec 2007 14:17:10 -0600

What Are Plastic-Lined Nipples And Why Do I Need Them?

Pipe nipples are small fittings that connect two pipes together. Many pipes and pipe nipples are made out of brass or copper because these metals are “noble” metals. This means that brass and copper do not chemically react with oxygen—the cause of corrosion or rusting—as much as other metals do (such as steel). The hot and cold water lines on top of the water heater are usually made of brass or copper. Unfortunately, most water heater tank linings and pipes are made out of steel. If these different metals touch each other, the brass or copper will actually promote rusting on the steel tank while the brass or copper remain rust free.

How To Inspect a Leaky Water Heater

johnnyhayneser — Thu, 29 Nov 2007 12:41:57 -0600

Inspect your fittings. Don’t know which fittings you need to inspect? Check all of the following; make sure the fittings are tight and dry. Use a cotton swap or Q-tip to wipe around the areas to make sure they are free of moisture and rust.

read more

How To Shrink Power Bills by Conserving Energy with your Water Heater

johnnyhayneser — Tue, 27 Nov 2007 14:37:39 -0600

This article teaches you how to save money by instituting all the following devices: Electric temperature controls, heat traps, low-flow shower heads, pipe insulation, recirculating system controls, vent dampers and water heater blankets.

Electric Temperature Controls (Electric Water Heaters Only). An electric temperature control allows you to shut down the water heater when no one is home or when everyone is asleep. This will reduce heat loss and save you money. Call your utility company or a plumber to help you install this device.

How To Save Yourself from Cold Showers by Knowing More About Dip Tubes

johnnyhayneser — Mon, 26 Nov 2007 19:43:59 -0600

Standard Dip Tubes. A dip tube is a long, straight plastic pipe attached to the cold water inlet, above the water heater, and into the tank of the water heater itself. Its purpose is to ensure that new cold water enters the tank at the bottom. Hot water naturally rises above cold water, so the hot water will be used first since the hot water outlet is at the top of the tank. If the dip tube breaks, cold water will enter at the top of the tank and will be immediately sent through the hot water outlet. This results in a cold shower or bath.

read more

How To Handle Corrosion Problem Spots in a Water Heater

johnnyhayneser — Mon, 26 Nov 2007 18:57:01 -0600

Corrosion can cripple the life of your water heater no matter if you have a tank-type, commercial or solar water heater system. Learn where the 7 trouble spots for water heaters are and how to protect your water heater from corrosive elements.